In mechanics, work is produced by a following force. Force causes motion, and the product of the two is work. When force stops, work stops, though motion may continue. Work, like heat, is a form of energy. The customary units of work are foot-pounds, or Newton-meters if you prefer.
Most people find power more interesting than work. Power is the rate of doing work. We can think of power as latent and potential, lurking under the hood, or power as manifest, a visible display of force and energy.
James Watt wished to claim that his newly invented steam engine could do the work of several horses. To support his claim he measured the power of a horse by various means. For example in 1783 he showed that a horse walking at 2.5 miles per hour could easily raise a 100 pound weight out of a well, using a rope and pulley. Two and a half miles per hour is 220 feet per minute. So, this horse was working at the rate of 22,000 foot-pounds per minute. Other experiments convinced Watt that this estimate was too low, so he increased the number by 50% and arrived at 33,000 foot-pounds per minute as a reasonable estimate of the power of a horse. This is the definition of horsepower still in use.
A small horse can produce one horsepower for a time, but horse handlers report that even a large horse will tire if required to do a day’s work at this rate. Unlike Watt’s engine, people and animals grow tired when they work. Yet we can do work at a high rate for a short time.
If an athlete weighing 110 pounds can run up stairs at the rate of 5 feet of vertical ascent per second, this very vigorous individual is producing one horsepower. If the athlete weighs 220 pounds, he only needs to ascend at 2.5 feet per second to produce one horsepower. One horsepower may be easy for a horse, but it is near the upper limit of a human athlete’s short-term capability.
In 1997 the bicyclist Marco Pantani ascended an Alpine grade of 8.89 miles in a record time of 37 minutes 35 seconds. The vertical ascent was 3749 feet. Pantani reportedly weighed 126 pounds, and his bicycle 15 pounds. If we do the math we find that he produced on average 0.43 horsepower in making this ascent. But his gear might have added a little more weight, and wind resistance at 15 miles per hour would have called for a little more power. We can reasonably claim that this athlete produced about half a horsepower for about half an hour. It might be hard to find an example of greater power produced by any person for a comparable length of time, especially if we ask for horsepower per pound of body weight.
Every moving thing is moved by a force, or was moved by force at the outset of its motion. If we ask narrowly what is moving, and what caused that motion, the answers will invoke virtually all of the physical sciences and will identify all of the forces of nature.
We will also identify artifacts that move by design, like vehicles, boats, motors and projectiles. Sometimes we employ natural forces, like the wind, to move those artifacts. More often we devise an artificial way to produce the force and do the work. We can list all the practical sources of main force. They are
• Living tissue: muscle power.
• Gravity: for example, descending water.
• Magnetism and electromagnetism, as employed for example in electric motors.
• Elasticity: The wound spring or compressed gas, in which force is applied now and recovered later.
• Dynamic force arising from Newton’s second law, in which the velocity of some mass is altered. Greater mass, or greater altering, generates greater force. This force propels a leaf blowing in the wind, or a sailboat.
• Thermal expansion, including the expansion of hot gas as typically harnessed in engines. There are various ways, including combustion and detonation and nuclear fission, to produce the hot gas.
Electrostatic force is difficult to harness but is occasionally put to use. Osmotic pressure can lift a liquid, however slowly. Nuclear physics identifies small-scale forces that have not been put to use by engineers. Cosmologists speculate about large-scale forces that are not perceptible here on earth.
One method commonly employed to move a vehicle or other object is to purchase traction on the surface of the earth, and push or pull. The horse’s hoof and the powered wheel on pavement are two examples. The gondolier’s pole on the bottom of the canal is another. In each case a force is applied to the earth. Because the earth is immovable, or nearly so, the vehicle moves and the force follows with it.
Another way to move an object forward is to accelerate fluid aft. This is a concise description of the mechanism that propels a rowboat, a rocket, a propeller-driven ship or plane, a jet plane, a turbine and a sailboat.
The working fluid might be air, or water, or some gaseous product of combustion. To accelerate the fluid is to change its velocity. Velocity has both a direction and a magnitude. To accelerate a fluid aft is to thrust it backward, or to give it a new direction that is more nearly backward. By Newton’s Second Law, the force that accelerates the fluid backward will be the product of mass and acceleration. By Newton’s Third Law, the rearward force on the fluid will be matched by a forward force on the vehicle.
The rocket motor, for example, accelerates its gaseous inventory straight back at high velocity as it burns. The rocket is perhaps the simplest example of driving a vehicle forward by accelerating fluid aft.
A more complex and more instructive example is the sailboat.
First consider a sailboat running before the wind. The sails do not reverse the direction of the wind and send it aft. The following wind is not even stopped; it is merely slowed. But that slowing is acceleration toward the stern, and Newton’s Second Law will quantify the force that drives the sailboat forward by accelerating wind aft.
Now consider a sailboat steering east on a north wind. The course is called a reach. The sailor sets the sail to capture wind from the north and bend it toward the west, which is aft. Because the boat is making headway east, the wind seems to be coming not from due north but from east of north. The leading edge of the sail must point directly into this wind, for any other set would slow the wind and slow the boat. The trailing edge of the sail points aft, or nearly aft. Lines tied aft are taut. The boat is pulled forward.
It is obvious that wind entering the windward or inside curve of the sail must turn aft, following the curve. But the front side of the sail has a positive curvature. It is not so obvious that wind passing in front of the sail will be turned aft, but in fact it is. Explanations usually note that the outside of the sail is curved like an airplane wing; it is an airfoil. Air passes over an airfoil and creates a low pressure which is called lift. Lift in front of the sail pulls the craft forward. All this is true, but it is also true that the low pressure on the front surface of the sail causes air to accelerate back toward the sail, which is aft. The Newtonian description of the sail’s function remains valid.
Now suppose the sailor steers a few degrees north of east, angling into the wind. The course is called a tack or beat. As long as the boat is making headway the sailor can steer the course. The keel and rudder will overcome any tendency of the wind to move the sailboat sideways. The interaction of wind and sail is not fundamentally different from the reach. But now the apparent wind direction is closer to the bow, and more nearly due aft, so less turning of the wind is possible and therefore less reaction force is available to drive the boat forward. Also, the force of the wind against the hull and rigging is farther forward, working against headway. At some point as the sailor steers ever closer to the wind, setting the sail’s leading edge more nearly forward, the sailboat can no longer make headway.
The familiar three-bladed wind turbine is like a sailboat on a reach. The similarity is not in form, but in function. The blade, like the sail, moves at a right angle to the wind. The blade’s shape and set are designed to turn the wind aft, opposite to the direction of rotation.
To think about the blade’s shape and set, imagine each blade is a row of sails attached by rigging to a mast. Three masts with their rows of sails form the wind turbine’s rotor. We will engage a sailor to ride each mast in a boson’s chair and to set each sail as he would do on a sailboat.
Imagine the sailor faces the direction of rotation. The wind is from his left. At a location near the hub, the rotational speed of the blade might be about equal to the wind speed. Then the wind will appear to be coming not from the left, but from the left front at 45 degrees. The sailor will set the leading edge of this inboard sail at 45 degrees, and fasten the trailing edge so that it curves back toward himself. Wind enters the sail and turns aft, pushing the mast forward.
As the sailor moves up the mast, the speed in the direction of rotation increases while the wind speed remains constant. The apparent wind direction moves closer to the front. At the last sail location, corresponding to the blade tip, the blade speed might be five or six times the wind velocity. Then the wind will appear to be coming from only about ten degrees left of the direction of motion. The sail is set accordingly. The contribution of the blade tip to the work of the wind turbine is obtained by turning the wind through an angle of only ten degrees. That is not a lot of turning, but on the other hand there is a great deal of air to be turned at this distance from the hub.
No sailboat on a reach achieves a forward velocity of even twice the wind speed. The hull and keel, as well as the mast and rigging, all create drag forces that limit the speed. An iceboat can achieve five times the wind speed, because drag forces are much smaller. The well-designed wind turbine blade produces so little drag that it can still generate net force in the direction of rotation at a speed six times the wind speed.
Our row of sails will not make a satisfactory turbine blade, because these sails cannot be continuously reset as the wind changes. Sails would luff when the wind speed drops. The apparent wind direction would move farther forward and shake or collapse the leading edge of the sails. The actual blade will have a fixed shape that is strong and rigid, and it will have a leading edge that is blunt like an airplane wing, rather than thin like a sail. The blunt leading edge and rigid airfoil shape make the blade stable, tolerant of changes in the wind speed, still producing net forward force under varying conditions. The blade’s airfoil shape will be twisted, like the row of sails, which we set at 45 degrees near the hub and only 10 degrees at the tip.
Having discussed acceleration of fluids, one might ask why acceleration of solids is not also a useful way to generate a force and propel an object. Examples are few, because acceleration of solids is inconvenient compared to acceleration of liquids and gases. But consider a rifle firing a bullet. Hot pressurized gas is generated by detonation in the chamber. The bullet is accelerated forward, and the rifle backward, each at a rate inversely proportional to its mass. The pressurized gas in the barrel merely transmits force between bullet and rifle. We can say that the bullet moves forward by accelerating the rifle aft. Or from the rifle’s perspective, the bullet is accelerated aft.
Now suppose the rifle butt is placed securely against a large boulder. The rifle does not move when it is fired. The rifle moves the bullet forward by securing a foothold on the earth, and pushing, just as the horse moves the cart forward by planting a hoof and pushing. We are back to Newton’s third law, not needing the second law to explain why the bullet leaves the barrel.
Friday, October 20, 2023
Subscribe to:
Post Comments (Atom)

No comments:
Post a Comment