Friday, October 20, 2023

Twenty-eight. In mechanics...

In mechanics, work is produced by a following force. Force causes motion, and the product of the two is work. When force stops, work stops, though motion may continue. Work, like heat, is a form of energy. The customary units of work are foot-pounds, or Newton-meters if you prefer.

Most people find power more interesting than work. Power is the rate of doing work. We can think of power as latent and potential, lurking under the hood, or power as manifest, a visible display of force and energy.

James Watt wished to claim that his newly invented steam engine could do the work of several horses. To support his claim he measured the power of a horse by various means. For example in 1783 he showed that a horse walking at 2.5 miles per hour could easily raise a 100 pound weight out of a well, using a rope and pulley. Two and a half miles per hour is 220 feet per minute. So, this horse was working at the rate of 22,000 foot-pounds per minute. Other experiments convinced Watt that this estimate was too low, so he increased the number by 50% and arrived at 33,000 foot-pounds per minute as a reasonable estimate of the power of a horse. This is the definition of horsepower still in use.

A small horse can produce one horsepower for a time, but horse handlers report that even a large horse will tire if required to do a day’s work at this rate. Unlike Watt’s engine, people and animals grow tired when they work. Yet we can do work at a high rate for a short time.

If an athlete weighing 110 pounds can run up stairs at the rate of 5 feet of vertical ascent per second, this very vigorous individual is producing one horsepower. If the athlete weighs 220 pounds, he only needs to ascend at 2.5 feet per second to produce one horsepower. One horsepower may be easy for a horse, but it is near the upper limit of a human athlete’s short-term capability.

In 1997 the bicyclist Marco Pantani ascended an Alpine grade of 8.89 miles in a record time of 37 minutes 35 seconds. The vertical ascent was 3749 feet. Pantani reportedly weighed 126 pounds, and his bicycle 15 pounds. If we do the math we find that he produced on average 0.43 horsepower in making this ascent. But his gear might have added a little more weight, and wind resistance at 15 miles per hour would have called for a little more power. We can reasonably claim that this athlete produced about half a horsepower for about half an hour. It might be hard to find an example of greater power produced by any person for a comparable length of time, especially if we ask for horsepower per pound of body weight.

Every moving thing is moved by a force, or was moved by force at the outset of its motion. If we ask narrowly what is moving, and what caused that motion, the answers will invoke virtually all of the physical sciences and will identify all of the forces of nature.

We will also identify artifacts that move by design, like vehicles, boats, motors and projectiles. Sometimes we employ natural forces, like the wind, to move those artifacts. More often we devise an artificial way to produce the force and do the work. We can list all the practical sources of main force. They are

•   Living tissue: muscle power.
•   Gravity: for example, descending water.
•   Magnetism and electromagnetism, as employed for example in electric motors.
•   Elasticity: The wound spring or compressed gas, in which force is applied now and recovered later.
•   Dynamic force arising from Newton’s second law, in which the velocity of some mass is altered. Greater mass, or greater altering, generates greater force.  This force propels a leaf blowing in the wind, or a sailboat.
•   Thermal expansion, including the expansion of hot gas as typically harnessed in engines. There are various ways, including combustion and detonation and nuclear fission, to produce the hot gas.

Electrostatic force is difficult to harness but is occasionally put to use. Osmotic pressure can lift a liquid, however slowly. Nuclear physics identifies small-scale forces that have not been put to use by engineers. Cosmologists speculate about large-scale forces that are not perceptible here on earth.

One method commonly employed to move a vehicle or other object is to purchase traction on the surface of the earth, and push or pull. The horse’s hoof and the powered wheel on pavement are two examples. The gondolier’s pole on the bottom of the canal is another. In each case a force is applied to the earth. Because the earth is immovable, or nearly so, the vehicle moves and the force follows with it.

Another way to move an object forward is to accelerate fluid aft. This is a concise description of the mechanism that propels a rowboat, a rocket, a propeller-driven ship or plane, a jet plane, a turbine and a sailboat.

The working fluid might be air, or water, or some gaseous product of combustion. To accelerate the fluid is to change its velocity. Velocity has both a direction and a magnitude. To accelerate a fluid aft is to thrust it backward, or to give it a new direction that is more nearly backward. By Newton’s Second Law, the force that accelerates the fluid backward will be the product of mass and acceleration. By Newton’s Third Law, the rearward force on the fluid will be matched by a forward force on the vehicle.

The rocket motor, for example, accelerates its gaseous inventory straight back at high velocity as it burns. The rocket is perhaps the simplest example of driving a vehicle forward by accelerating fluid aft.

A more complex and more instructive example is the sailboat.

First consider a sailboat running before the wind. The sails do not reverse the direction of the wind and send it aft. The following wind is not even stopped; it is merely slowed. But that slowing is acceleration toward the stern, and Newton’s Second Law will quantify the force that drives the sailboat forward by accelerating wind aft.

Now consider a sailboat steering east on a north wind. The course is called a reach. The sailor sets the sail to capture wind from the north and bend it toward the west, which is aft. Because the boat is making headway east, the wind seems to be coming not from due north but from east of north. The leading edge of the sail must point directly into this wind, for any other set would slow the wind and slow the boat. The trailing edge of the sail points aft, or nearly aft. Lines tied aft are taut. The boat is pulled forward.

It is obvious that wind entering the windward or inside curve of the sail must turn aft, following the curve. But the front side of the sail has a positive curvature. It is not so obvious that wind passing in front of the sail will be turned aft, but in fact it is. Explanations usually note that the outside of the sail is curved like an airplane wing; it is an airfoil. Air passes over an airfoil and creates a low pressure which is called lift. Lift in front of the sail pulls the craft forward. All this is true, but it is also true that the low pressure on the front surface of the sail causes air to accelerate back toward the sail, which is aft. The Newtonian description of the sail’s function remains valid.

Now suppose the sailor steers a few degrees north of east, angling into the wind. The course is called a tack or beat. As long as the boat is making headway the sailor can steer the course. The keel and rudder will overcome any tendency of the wind to move the sailboat sideways. The interaction of wind and sail is not fundamentally different from the reach. But now the apparent wind direction is closer to the bow, and more nearly due aft, so less turning of the wind is possible and therefore less reaction force is available to drive the boat forward. Also, the force of the wind against the hull and rigging is farther forward, working against headway. At some point as the sailor steers ever closer to the wind, setting the sail’s leading edge more nearly forward, the sailboat can no longer make headway.

The familiar three-bladed wind turbine is like a sailboat on a reach. The similarity is not in form, but in function. The blade, like the sail, moves at a right angle to the wind. The blade’s shape and set are designed to turn the wind aft, opposite to the direction of rotation.

To think about the blade’s shape and set, imagine each blade is a row of sails attached by rigging to a mast. Three masts with their rows of sails form the wind turbine’s rotor. We will engage a sailor to ride each mast in a boson’s chair and to set each sail as he would do on a sailboat.

Imagine the sailor faces the direction of rotation. The wind is from his left. At a location near the hub, the rotational speed of the blade might be about equal to the wind speed. Then the wind will appear to be coming not from the left, but from the left front at 45 degrees. The sailor will set the leading edge of this inboard sail at 45 degrees, and fasten the trailing edge so that it curves back toward himself. Wind enters the sail and turns aft, pushing the mast forward.

As the sailor moves up the mast, the speed in the direction of rotation increases while the wind speed remains constant. The apparent wind direction moves closer to the front. At the last sail location, corresponding to the blade tip, the blade speed might be five or six times the wind velocity. Then the wind will appear to be coming from only about ten degrees left of the direction of motion. The sail is set accordingly. The contribution of the blade tip to the work of the wind turbine is obtained by turning the wind through an angle of only ten degrees. That is not a lot of turning, but on the other hand there is a great deal of air to be turned at this distance from the hub.

No sailboat on a reach achieves a forward velocity of even twice the wind speed. The hull and keel, as well as the mast and rigging, all create drag forces that limit the speed. An iceboat can achieve five times the wind speed, because drag forces are much smaller. The well-designed wind turbine blade produces so little drag that it can still generate net force in the direction of rotation at a speed six times the wind speed.

Our row of sails will not make a satisfactory turbine blade, because these sails cannot be continuously reset as the wind changes. Sails would luff when the wind speed drops. The apparent wind direction would move farther forward and shake or collapse the leading edge of the sails. The actual blade will have a fixed shape that is strong and rigid, and it will have a leading edge that is blunt like an airplane wing, rather than thin like a sail. The blunt leading edge and rigid airfoil shape make the blade stable, tolerant of changes in the wind speed, still producing net forward force under varying conditions. The blade’s airfoil shape will be twisted, like the row of sails, which we set at 45 degrees near the hub and only 10 degrees at the tip.

Having discussed acceleration of fluids, one might ask why acceleration of solids is not also a useful way to generate a force and propel an object. Examples are few, because acceleration of solids is inconvenient compared to acceleration of liquids and gases. But consider a rifle firing a bullet. Hot pressurized gas is generated by detonation in the chamber. The bullet is accelerated forward, and the rifle backward, each at a rate inversely proportional to its mass. The pressurized gas in the barrel merely transmits force between bullet and rifle. We can say that the bullet moves forward by accelerating the rifle aft. Or from the rifle’s perspective, the bullet is accelerated aft.

Now suppose the rifle butt is placed securely against a large boulder. The rifle does not move when it is fired. The rifle moves the bullet forward by securing a foothold on the earth, and pushing, just as the horse moves the cart forward by planting a hoof and pushing. We are back to Newton’s third law, not needing the second law to explain why the bullet leaves the barrel.

Wednesday, October 18, 2023

Twenty-nine. Truth is a categorical imperative...

Truth is a categorical imperative, according the ethical philosophy of Immanuel Kant. Because Truth is Right, a lie is wrong. Kant elevated the Right and rejected the opposite. He resisted the notion that particular circumstances might justify the lie.

Kant was challenged in his time with the hypothesis of the Inquiring Murderer, in which a truthful answer will betray the murderer’s innocent victim. The more recent version of the dilemma would have the Nazis at the door and the Jews in the attic. Kant defended his intellectual edifice and rejected the lie, while refusing to be pushed into the hypothetical corner that must choose betrayal. His critics found his position unsatisfactory.

Most people then and now would agree that truth is right, but betrayal is wrong, and in these hypothetical circumstances the betrayal is so appalling and the lie so harmless that one must choose the lie. There is no categorical imperative. The ethical choice of truth or lie depends on the situation.

This much-discussed subject is raised here to introduce a question of interest to Christians. What would Jesus do?  We do not need to speculate recklessly. We have the guidance of many Gospel stories recounting what Jesus actually did in various circumstances. The answer to our question will be one that is consistent with all that we already know. If we can write a story that would raise no eyebrows in the Christian community, then we will gain some insight into what Jesus would do an encounter with the Inquiring Murderer.

The infant Jesus was himself the target of an Inquiring Murderer. The circumstances of his birth in Bethlehem identified him as a king, a contender for the throne. The enthroned king responded to this threat by ordering the death of every infant boy in Bethlehem. Jesus’ parents, warned in a dream, escaped to Egypt. We understand from this story that the infant Jesus’ life was preserved by the power of God.

Similarly the infant Moses in Egypt would have died under Pharaoh’s edict against male Hebrew infants. Pharaoh wished to control an alien population. Moses was spared by a benign deception, in which the saving hand of God is discerned by the faithful.

So we will put the Inquiring Murderer hypothesis in Jesus' time, and suppose that the adult Jesus is in a house when soldiers appear at the door, demanding to know what children are in the house. Their grim mission is understood.

Jesus is seldom alone; those with him might include his host, his disciples, followers, seekers and so forth. There would be more than one soldier, because one alone might shirk his duty. One would speak, and all eyes would turn to Jesus to give an answer. Jesus’ wisdom and authority were unquestioned by those who knew him. How would Jesus answer?

Jesus would not lie. The Christian community would consider it blasphemous to suggest Jesus would countenance a lie, let alone tell one. No Gospel story puts a lie in Jesus’ mouth. Other Biblical characters, like Rahab, did lie in similar circumstances. Rahab was honored for her refusal to betray. But Jesus would not lie. Neither would he betray.

Jesus would respond to the soldiers, the two or three of them, with words that revealed their hearts. This is typically the way he responded to strangers. He knew the hearts of men. He would expose the evil they sought to do. Each of them would know that he saw right through them, as we might say today. Each would respond to him by confirming what Jesus’ words had revealed. The hard heart would be angry or contemptuous; another might be dismayed or sorrowful. But we will not suppose that this revelation deters the soldiers. They are all hardened men, trained do their duty. One leads and the others follow. They burst into the house and search every room.

The last line in our story will say “Finding nothing, they went on their way.” We will be left to guess whether the child that had been in the house was whisked away by the power of God, or taken out the back by a quick-thinking nanny. Or perhaps one soldier, cut to the quick by the words of Jesus, saw the sleeping child but said nothing.

If our story is true to the Gospel accounts, the faithful will read it as one more account of the power of God that is in Jesus Christ. He is able to save. No one is able to take his own from him. Whoever is in his care is in God’s care.

So we have an answer to the question, What would Jesus do? But Jesus’ followers must still answer, What would I do?

Some insist they would do as Jesus did. They will not lie to save a life; they will trust God to save the life. Kant would approve, but Kant was an old man in his study. Kant did not need to invoke the power of God to defend his thesis, because no actual life was at stake. But a follower of Jesus cannot do as Jesus did in real circumstances unless he is assured that the power of God is in his hands and will and words. Misguided individuals sometimes act as if they had such assurance when they do not.

The vast majority of Jesus’ followers will not do as our story would have Jesus do. They will lie to avoid the betrayal, as Rahab did. Many wish to follow in the steps of Jesus. Some stay with him much longer than others, but no one is with him to the end. It is not just a question of knowing what to do, or having the courage to do it. We also lack the strength, or the power, to do what Jesus alone can do. He is perfect in all respects; we are imperfect in many. We fail to emulate Christ. Instead, we worship him. God alone is good; we are not.  Jesus saves; we cannot.

Jesus’ moral teaching is, to say the least, difficult to follow. Who will bear witness to the truth?  Who will love his enemy, and turn the other cheek, and give up all his possessions for Christ’s sake? Nearly every Christian will equivocate on these, believing it necessary, but Jesus did not equivocate. He lived his teaching during his short life, and then he died.

Our claim to life is not ours but his: God raised him up. We are his body. His resurrection is ours. Similarly our claim to righteousness is a claim to his righteousness, not to our own. God’s high standard is beyond us, and revealed in him.

Monday, October 16, 2023

Thirty. Dear Jalyse

Judy shared your letter of November 30 with me and other members of her family. Thank you for taking the time to write down your views on such an important question. With this letter I am doing something similar.

The doctrine of the Trinity is central to the Christian faith. Some say it is the central doctrine of the Christian faith. So, Christians should be prepared to defend it when called upon to do so, and that is my purpose here.

The New Testament often speaks of Father, Son and Spirit. I think you will agree that two or all three of these names often appear together in passages about God. We call these the Trinity. Our question is what is the relationship between Persons of the Trinity? To this question, different passages of scripture have been interpreted in different ways to arrive at different conclusions.

The Doctrine of the Trinity begins with the teaching that God is One. In this there is no possibility of error or misunderstanding of the teaching of Scripture. We worship the God of Abraham, and He is One. Jehovah is a name given since ancient times to the one true God.

Then each Person of the Trinity is either God, or not. The three cannot be a plurality of gods. And if one is subordinate to another, and less great, then they are not One God.

The Christian church does exalt Jesus Christ. When we must make a choice between two interpretations of Scripture, we choose the one that exalts Christ, and not the one that diminishes Him. As a man of flesh he is one of us. As God, He is true God, and not a lesser god.

We proclaim one God, one Father, one Son, one Spirit, one Savior, one King, one Judge, just to begin a list.

Yours in Him,

Joe

Monday, February 29, 2016

Marriage Service

Marriage Service

Words of Gathering
God is love, and those who abide in love abide in God, and God abides in them. This is the day the Lord has made. Let us rejoice and be glad in it.

Greeting
Dearly beloved, we are gathered here today in God’s presence, and in the presence of friends and loved ones, to join L and E in holy matrimony, and to celebrate with them in one of life’s greatest moments. Marriage is a most honorable estate, established and sanctified by God, and signifying the union which also rests between Christ and the Church. So too may this marriage be adorned by true and abiding love. May L and E cherish and delight one another; may they comfort and help each other in sickness, trouble and sorrow; may they provide for each other in temporal things; may they pray for and encourage each other and live together as heirs of the grace of life.

Opening Prayer
Almighty and ever-blessed God, whose presence is the happiness of every condition, and whose favor hallows every relation: We beseech you to be present and favorable unto these your servants, that they may be truly joined in the honorable estate of marriage, in the covenant of their God. As you have brought them together by your providence, sanctify them by your Spirit, giving them a heart fit for their new estate; enrich them with all grace, whereby they may enjoy the comforts, undergo the cares, endure the trials, and perform the duties of life together, under your guidance and protection; through Jesus Christ we pray. Amen.

Hymn or song
First Reading
Musical interlude
Second reading

Declaration of intentions
L C, will you have this woman to be your wife, and will you promise your life to her in all love and honor, in all duty and service, in all faith and tenderness, to live with her, and cherish her according to the ordinance of God, in the holy bond of marriage?
The groom shall answer ‘I will’.
E H, will you have this man to be your husband, and will you promise your life to him in all love and honor, in all duty and service, in all faith and tenderness, to live with him, and cherish him according to the ordinance of God, in the holy bond of marriage?
The bride shall answer ‘I will’.
Who gives this woman to be married to this man? Or, who gives this man and woman to be married?
Or …?

Charge to family and friends
Each of you are here today because you are part of the community where L and E will make their home. Therefore, having heard them state their intentions to each other and before God in this Service of Marriage, do you pledge to support their union and to strengthen their lives together?
The people shall answer ‘Yes, we do’.

Marriage vows
Here, the groom takes the bride's right hand with his right hand, and says, after the Minister: 

I, L, take you E, to be my wedded wife; And I do promise and covenant; before God and these witnesses; to be your loving and faithful husband; in plenty and in want; in joy and in sorrow; in sickness and in health; as long as we both shall live. 

Then the bride takes the groom's right hand with her right hand, and says likewise after the Minister: 

I, E, take you, L, to be my wedded husband; and I do promise and covenant; before God and these witnesses; to be your loving and faithful wife; in plenty and in want; in joy and in sorrow; in sickness and in health; as long as we both shall live. 

Exchange of Rings
Then the ring for bride shall be given to the Minister, who shall pass it to the groom, who shall then put it upon the bride's fourth finger, saying after the Minister: 

This ring I give you; in token and pledge; of our constant faith; and abiding love.

Then the ring for the groom shall be given to the Minister, who shall pass it to the bride, who shall then put it upon the groom's fourth finger, saying after the Minister: 

This ring I give you: in token and pledge: of our constant faith: and abiding love. 

Wedding Prayer
Let us pray.

Most merciful and gracious God, in whom we live and move and have our being, bestow upon these your servants the seal of your approval, and your benediction; granting them grace to fulfill, with pure and steadfast affection, the vow and covenant they have made. Guide them together, we ask, in the way of righteousness and peace, that, loving and serving you, with one heart and mind, all the days of their life, they may be abundantly enriched with the tokens of your everlasting favor, in Jesus Christ our Lord. Amen. 

The Lord’s Prayer

Pronouncement of Marriage
By the authority given to me by the Commonwealth of Massachusetts, I declare that L C and E H are now Husband and Wife, according to the ordinance of God, and the law of this State; in the name of the Father, and of the Son, and of the Holy Spirit. Amen 

Then causing the bride and the groom and to join right hands, 

Whom therefore God has joined together, let no one put asunder. 

Benediction
The grace of Christ attend you, and the Father’s love surround you, the Holy Spirit keep you, that you may live in faith, abound in hope, and grow in love, now and forever. Amen. 
Or,
May the grace of Christ your Savior
And the Father’s boundless love,
With the Holy Spirit’s favor
Rest upon you from above.
Thus may you abide in union
With each other and the Lord,
And possess in sweet communion,
Joys which earth cannot afford.

You many kiss the bride.

Ladies and Gentlemen, it is my happy privilege to congratulate and introduce to you

Mr. and Mrs. L C


Thursday, January 28, 2016

March 1933

Here are Virginia Nuckols and Joe Gilman at her parents’ home in Bell, California. This photo was taken probably a couple of years before they were married on March 20, 1933. I shall refer to Virginia and Joe as Mother and Dad.

Mother’s parents were Sam and Mae Nuckols. The Depression closed Sam Nuckols’ plumbing business in Bell. The Nuckols family would move from Bell to San Diego County, a hundred miles south and east, by 1933. Mother and Dad were married at the Nuckols home, “the ranch”, in the Pauma Valley near Pala.

They were married 10 days after the earthquake, as Dad often recalled. The Long Beach earthquake struck on March 10, and did considerable damage in Dad’s hometown, Huntington Park. Dad recalled that he got a haircut on March 10, and the earthquake struck later that afternoon. The barber ran into the street and was killed by a falling brick.

A few years ago when Mother was nearly 100 years old, she recalled to me that she visited the Gilman home shortly before the wedding, getting acquainted with her new in-laws-to-be, and shopping in preparation for her wedding.  There was a cash crisis on that day in the Gilman household. The banks had closed, and no one knew when they would open again. The elder Mr. Gilman needed to pay the mortgage. He asked Virginia, very politely, if she had any money. Yes she did, and her money was readily accessible, because she had her savings in postal savings certificates and not in the bank. So all was well; she made the loan. In that same phone conversation with me, Mother recalled that she spent some of her savings on material for her wedding dress, which she took home to sew. After the wedding the newlyweds would cash in her remaining postal savings certificates to buy a used car.

Her visit to Huntington Park was just days before the earthquake. This was the bottom of the Depression, as Dad liked to say. Banks were in crisis. California banks closed on March 3, and President Roosevelt was inaugurated on Friday the 4th. His first action was to close all banks nationally. They would not open again until Monday the 14th, which was after the earthquake. Mother’s visit must have been the weekend of March 5 and 6. She finished her shopping and was back home making her dress by March 10, so she did not experience the earthquake.

My sister Virginia recalls another earthquake story as told by Dad. Sometime between March 10 and March 20, Mother would be baptized in Dad’s church, the Huntington Park Christian Church. The church building had been damaged by the earthquake. Some of the roof was open to the sky. Nevertheless the baptistry was operational. Dad recalled, fondly, that a ray of sunshine came through the roof and illuminated his bride-to-be just as she came up out of the water. Dad said much later in life that this was the most beautiful sight he had ever seen.

The pastor who performed the baptism, and the wedding ceremony, was Kelly O’Neal. He and Mrs. O’Neal are on the right in this photo of the wedding party at the ranch. Others from left to right are Roland Nuckols, Hallie Westlund, Virginia and Joe, Gene Nuckols, Bill and Virgie Byles, Sam and Mae Nuckols, and Joe and Stella Gilman. My cousin Betty remembers the day, but she was deemed too small to make the trip from Huntington Park. I think she is still a bit miffed about that.

Mother and Dad made their first home in Huntington Park, or close by. Dad still worked for the Santa Fe Railway, but Santa Fe had reduced his grade, pay and hours to keep him on the payroll throughout the Depression. He worked half time, and Mother worked half time as a beautician. She could have worked full time, but she thought she ought not to work more hours than her husband. Mother recalled that their grocery budget, after all the bills were paid, was seven dollars and change per week. They lived well on seven dollars, she said.


Joe D. Gilman, Jr

Friday, February 6, 2015

Projects

This is not the story of my life. That would be the story of my life with Judy; with our children as they came; with extended family and with friends; the Sundays and birthdays and weddings and churches and schools and graduations and celebrations and funerals; all the places we went, and the way we got there; eating out and staying home; being away and coming home and telling our stories.
Alongside all of this family living and loving and growing, I worked from time to time on projects. I have described myself as project oriented. Projects were usually, for me, a solitary activity. A project has a beginning and an end. A project produces something. My projects might produce something needed and useful, or something merely interesting, at least to me. (Incidentally, I have seldom worked on a project that produced what the world would call art.) In my professional work as an engineer, I often worked on projects that produced something on paper. I wrote many technical reports. At home, I might have remodeled the house or landscaped the yard or fixed a toaster. In retirement my woodshop project might produce a piece of furniture. In childhood, the goal of my project would typically be to make something that worked.
I am writing about projects not because my project descriptions will be particularly interesting to a reader, but because I remember each one after many years. My father said he remembered everything he ever did, speaking of his work as an electrician. He wired hundreds of houses. (I helped him wire a few dozen.) Many were similar but no two were the same. The differences were in the details, and every detail of his completed project had to be correct and functional and tight and legal and checked out. If he chose to run a cable or a circuit by an unusual route for some unusual reason, he remembered having done so.
When I was quite small I sat on the carpet with my Tinkertoys and worked at making the thing I saw pictured. I selected the pieces and counted the holes and put the thing together, or tried to. I preferred to make a thing that worked, like a crane with a crank and string and hook that could actually lift something. I’m sure my projects were not always successful, but I never thought I couldn’t do it. At some point I acquired an electric motor that was made to fit a Tinkertoy project, but I think I jammed the gears before long so the motor wouldn’t work. Later I took the motor apart and found that the electrical heart of it would still run, so I kept and valued that motor just because it worked. I stepped up to an Erector set, with its nuts and bolts and motor. My cousin Fred gave me his old Erector set to add to mine, so I could do the grandest projects like the Ferris Wheel.
Meanwhile, I also had an electric train. My project was to set it up and see it work. When I was 13, or maybe 14, I had earned some money and decided to spend it on a bigger and better electric train. My parents let me know they thought I was too old for such toys, but they relented. I wanted to set it up and make it work. I wired it so the lights would operate and the track would switch and the gate would drop as the train approached. I was not much interested in creating the model village. I liked the moving parts.
I made two or three electric motors during this time. I looked in some of my father’s books and figured out what the simplest motor would look like. I made the iron parts from scrap with a hacksaw and file. My Erector set provided the shaft, and Dad gave me bellwire for the windings. The commutator and brushes were probably the most difficult design challenge. The power source for my motor was a pair of big dry cell batteries, or maybe the transformer from my train set. At some point I made a wheeled vehicle (with the erector set) which carried the homemade motor and two dry cell batteries, and propelled itself down the sidewalk.
When I was sixteen I acquired an old car, which of course needed work. That was the end of lesser projects like trains and motors. After a series of repair and refurbish projects I had a decent running car. My father was a ready source of technical advice, and my mother sewed a new headliner using the old one for a pattern. My father also gave me a job, as an apprentice electrician, working with him on Saturdays and through the summer, which provided the income that financed the car projects. In retrospect I would say that the primary goal of my car refurbishing project was to enable a social life in high school, which it did. But that’s another story.
Earlier, at the age of eleven, I joined the Boy Scouts. I made friends and had fun. I also worked on projects, called merit badges. I was motivated to earn merit badges because the requirements and the end product were clear, and because I could do some of these by myself. (I had help and advice from my parents on some of these, but that didn’t make them group projects.) So I learned the knots; I hiked and swam the distance; I built a campfire and cooked a meal on it; I played music; I raised pigeons; I planted a garden, and so forth. Adults and peers approved. I’m sure that was also important to my motivation.
I earned a merit badge for bicycling by riding great distances with two friends. I recall this adventure as attached to friendship, not to projects or awards. On three occasions we rode from Compton east to Knott’s Berry Farm, and west to Redondo Beach, and south to Long Beach. Later I realized that Mom and Dad made a deliberate decision to let me take risks and learn about the world, rather than to grow up sheltered and unaware.
At about this time I had a thought, just a passing thought, which would stay in my memory and point in the direction of many future projects. We had a shed out back which had been cleaned out. I thought, as boys will do, that it would be great if this shed could be my private abode. I thought, perhaps a bit oddly, that if this space were mine I would have charts on the walls. The charts would depict information like, for example, the weather. I didn’t think so much about what information would be up there, but the idea of charts and graphs appealed to me. I must have recently learned what a chart is, and how it records and conveys information. Later I would spend a considerable portion of my professional life as an engineer in making charts and graphs; they were often a product of some technical project I had worked on.
I don’t think of education as a project. The goal of education is not a diploma or a report card, it is education. Education is too open-ended to be a project.  A term paper is a project, but aside from these I can’t recall many memorable projects that I completed in high school or college. I remember the classes and many of the teachers. I did assigned tasks like tests and homework. I did, and still do enjoy learning.
An exception would be my Senior Project, memorable and aptly named, in mechanical engineering at Cal Poly. I chose the topic from a list. I designed and built a contraption which would demonstrate vibration measurement with electrical resistance strain gages. The hardware consisted of an electric motor mounted on a flat cantilever beam with a heavy base. The motor rotated eccentric weights which caused the beam to vibrate. I used a rheostat to control the motor speed, and an oscilloscope to display the output. I had a budget from the department to purchase materials, and I had access to the machine shop to manufacture the parts. As I recall, I had the results in hand and the report written before I talked to any professor about it. Later as an engineer I would be responsible (in part) for just such vibration measurements in operating components of a nuclear power plant.
I read many books; some in childhood and many after college, when I had time. To read a book might be viewed as a project, because there is a beginning and an end. But often there is no salient end product. At best, a book is educational. To read a good book adds another brick to the never-finished edifice of one’s education. Non-fiction is educational, and a good novel is educational as well. We can learn something about people and places and the flavor of an era that would be difficult to pick up any other way.
When I started college we were expected to declare a major immediately, and to take a course or two directly related to that major. I enrolled in Architectural Engineering, because the building trades were already familiar to me and to my family. Soon I decided to change to Mechanical Engineering. That was the right choice.
Upon graduation in 1960 I took a job with General Electric Company. Their “Atomic Power Equipment Department” was headquartered in San Jose. My first assignment was located 25 miles away at Vallecitos. I worked for six months at GETR, the General Electric Test Reactor. My roommates in a San Jose apartment were all Cal Poly graduates, employed by either GE or IBM as I recall.
This would be the first of several six-month engineering training assignments, to be interrupted by two years of military service. At GETR I would assist with an ongoing project, construction of the AGN test loop. AGN meant Aerojet General Nuclear; they planned to test fuel for a proposed nitrogen-cooled reactor. The “AGN loop” in GETR replaced an older “ANP loop”.  ANP meant Aircraft Nuclear Propulsion; an idea that was fading in 1960. I had tasks and duties directly related to the hardware for the new loop. I learned to work in a nuclear reactor environment, with its rules and protocols for radiation monitoring. On one occasion I worked briefly inside the reactor vessel, installing a pipe support bracket of my own design. I worked with two senior engineers, three of us in a small office at the reactor site.
In 1961 and 1962 I served in the US Army, having received a commission through the college ROTC program.  I spent about five months in training at Aberdeen Proving Ground in Maryland, and the remainder of two years at Pinder Barracks in Germany, in the village of Zirndorf. As a junior officer in the peacetime Army I had tasks and duties and responsibilities, but I can’t say I accomplished anything that could be called a project. I learned something about people and places. I made many friends, mostly junior officers like myself. We took every opportunity to explore western Germany, and Western Europe. Shortly after my arrival in Germany, Khrushchev would order the construction of the Berlin Wall. Before I left, President Kennedy would deal with the Cuban Missile Crisis. We had those events to talk about, but we never heard a shot fired in anger, as the old soldiers liked to remind us. I would be home for Christmas at the end of 1962.
In 1963 I returned to GE and worked a second six-month engineering training assignment in San Jose. My job was to complete the development of an experimental device so it could be placed into an operating reactor, the Vallecitos Boiling Water Reactor. The flux cycler was already built. A small water turbine spun a train of gears, causing fuel rods to be alternately shielded from and exposed to neutron flux. One of my tasks was to find a gear and bearing material that would serve for weeks with no lubrication but hot water. I read papers on tribology and learned about wear-resistant alloys. The larger goal was accelerated performance testing of stainless steel as a fuel cladding material, to see whether stainless steel could serve as an alternative to zirconium cladding in the core of a nuclear power plant. Stainless steel cladding in trials was not performing well. My immediate supervisor, George Reiger, believed that the cause of failure might be low-cycle fatigue, meaning too much flexing back and forth as a result of heating and cooling. The flux cycler would test that hypothesis. But meanwhile evidence was showing that the cause of failure was stress corrosion cracking, not fatigue.
In this assignment I learned two things that would become part of my stock in trade for the next 35 years. First; George Rieger had a technical paper authored by Tavernelli and Coffin at GE’s R&D lab, showing that low cycle fatigue life of materials like stainless steel was correlated with the number and amplitude of plastic strain excursions imposed by service conditions. I did calculations of plastic strains in a thin-walled tube, resulting from external pressure that collapsed the tube onto the cylindrical fuel pellet. The paper by Tavernelli and Coffin was to be the basis for interpreting our aborted experiment, but, far more importantly, that paper became the basis for fatigue design of nuclear power plant components. I suspect the work had been done some years earlier for the nuclear navy, but that Tavernelli and Coffin were not permitted to publish until 1962. Their work had already found its way into design rules for pressure components in naval and commercial nuclear power plants. The principle was central to much of the work I would do later. And later I would have the pleasure of meeting and working with Lou Coffin in Schenectady from time to time.
The second portentious lesson from this time was simply the failure of stainless steel by stress corrosion cracking in the reactor environment.  Many plant components were manufactured from stainless steel, and some of these (too many!) would eventually exhibit the same cracking that was being observed in experimental fuel cladding in 1963. It is an understatement to say that stress corrosion cracking became a costly problem for the industry. Many people, including me, would derive a sizable fraction of their income dealing with issues surrounding intergranular stress corrosion cracking in weld-sensitized Type 304 stainless steel in the Boiling Water Reactor environment. The technical jargon is so familiar to me, I can’t say it any other way.
Upon returning to San Jose in 1963 I found an apartment and lived alone until I found a roommate. In that small apartment I assembled an FM tuner and a stereo amplifier; an excellent project for me at the time. I purchased Eico kits and followed the instructions, soldering the joints on the kitchen table. I also made wooden cabinets for speakers. Those components served for many years. Eventually the vacuum-tube technology became hopelessly obsolete and I threw them out.
At GE my next training program assignment, beginning in August of 1963, was with Dr. Howard Cook. I would design something called an Observational Test Section, in which water as it boiled could be directly observed. This water would boil at a temperature of 550 degrees Fahrenheit, under pressure of 1000 pounds per square inch. Windows of crystal sapphire, artificially grown, could withstand this pressure and temperature while passing light or X-rays. Dr. Cook wanted to measure the void fraction; the proportions of steam and water in the mixture as boiling progressed in a vertical channel. The configuration of my test section would not be circular, like most pressure vessels. It was linear and massive. Inside, water flowed past a long, narrow electric heater.
In October of 1963 I was sitting at a staff meeting in Dr. Cook’s office. Through the open door I noticed a young woman talking to our secretary Karen Wright. This was the first time I saw Judy. She had long auburn hair. After the meeting I asked Karen who she was. I also asked whether Judy would be coming to the upcoming Halloween office party at a local pizza place. Karen had the presence of mind to say yes, Judy will be coming with me. So I met Judy at the Outhouse in San Jose on or before Halloween night, and we shared a pizza. Judy will report that it was a long time before I called her. In fact it was November 25, the day of President Kennedy’s funeral. Her name and number were in the phone book, but it was the wrong number; she had moved. And she had changed her hair since I first saw her – that may have slowed me down a little. Eventually I contrived to stroll past her desk and ask for her phone number. When I finally did call, I was oblivious to the fact that JFK’s funeral was being broadcast on national television at that moment. I had a tiny little TV; I seldom watched it for long; and I would certainly not have been watching TV on the night I intended to call a certain girl. So I did call, and the rest is history.
I finished my tour of duty with Howard Cook in March of 1964, a few weeks after Judy and I had announced we were engaged to be married. The drawings for my project had been issued and the parts were being manufactured. Later I learned that the assembled and operating test section had blown a gasket. The blowout made a mess, but fortunately no one was hurt. I was to blame, and I was blamed, but I had moved on. I didn’t even hear about the incident until two or three years later. It became food for thought: how did I let this happen? The gasket that failed needed a retainer. In retrospect, I can see that a sandwich of metal and insulating washers would have sufficed. It was a design detail that could be left to the end. I did leave it to the end, and then I failed to take care of it. Several years later, the Nuclear Regulatory Commission would require a formal and documented design review process for every nuclear plant component. GE would require such a review across the board; even for non-nuclear hardware like this. I would have been required by this process to lay all the drawings on the table and explain all of it to a couple of senior design engineers. Surely one of us would have noticed that this non-metallic insulating gasket needed a retainer, and none was provided.
I may have been distracted by events in my personal life. Judy and I saw a lot of each other in December but went separate ways for Christmas. At home for a week or so in Downey, I said nothing about having met this girl, but I was working at divesting myself of all but the future. We picked it up again and were engaged on Valentine’s Day. Our wedding date would be July 25.
Judy and her family attended Westminster Presbyterian Church in San Jose. I had visited Wes Pres and several other churches in San Jose as a single man, new in town, but I kept a low profile and was not known in any of them. I attended Westminster Presbyterian with Judy, and the church became a central part of the environment in which our relationship thrived. In my young life I had been inside and outside of the church, but when I met Judy, each of us chose a spouse who was at home in the Christian church.
In March of 1964 I began a third six-month assignment, reporting to Sam Tagart. The following year I would take a permanent position with Sam, and our association would continue until and even after he left GE more than 10 years later. I was assigned projects typical of those I would work on in the future. I was first introduced to the computer during this period. A heat transfer program called TIGER had been written some years earlier by Phil Bray, who was Sam’s boss by 1964. TIGER was capable of calculating temperatures in fuel and cladding in a boiling water reactor core. It ran on GE’s mainframe Philco computer, which occupied a large room but was very small by today’s standards, in terms of capability. In college in the late 1950s my course work in mechanical engineering never touched on the computer. My roommate was studying electronics engineering; he talked about Boolean algebra and migration of plus holes in semiconductors, but I knew nothing about computers until 1964.
For readers who know the difference, TIGER was a finite difference program. A finite difference program like TIGER would run on a smallish computer.  A few years later we would have finite element programs for heat transfer and stress analysis, and suitably larger computer capacity.
Sam Tagart showed me a paper published a few years earlier, entitled “A Rational Analytic Theory of Fatigue.” He wanted to apply this innovative method to answer questions in our purview. The paper by Paris, Gomez and Anderson introduced the Paris Law, as it became known, for predicting the growth rate of cracks in metallic components. Sam’s instincts were good. During the next 30 years or more, I would complete many projects related to applications of the Paris Law, and I would participate with others in many more. Laboratories were producing data on crack growth rate that would be interpreted in terms of the Paris Law. We needed to know how a cracked component would perform in service, and for how long. I applied the method to the end cap on a fuel rod, in which the closure weld produces a configuration equivalent to a tight crack.
The Paris Law was an application of fracture mechanics. Paul Paris was a longtime collaborator of George Irwin, who was considered to be the father of engineering fracture mechanics. Irwin had worked since the 1940s to make fracture mechanics a practical engineering tool, applying it first to Navy ships. I began collecting papers and educating myself, making Irwin’s engineering fracture mechanics a tool of my trade, and applying it to projects at GE. Later, in 1967, I attended a short course taught by Irwin at UC Berkeley.
The record shows that I wrote 7 technical reports during these six months with Sam Tagart. I looked for example at contact stresses in fuel cladding produced by wire spacers, and the possible effect of these on long-term integrity of the cladding. I looked at fuel distortion and its possible effect on clad integrity. A cylindrical ceramic pellet producing internal heat will take an hourglass shape. The deformation would be small but predictable. The fuel designer needed assurance that this scalloping effect would not be detrimental to fuel clad integrity.
I looked at the Vallecitos Superheat Reactor to see what loads and stresses would result from an earthquake. Much later I would manage a team of engineers doing seismic and dynamic analysis. This early project was a beginning.
The last of my six-month training assignments would be with K. Hikido, looking at fuel cladding design for SEFOR, a sodium-cooled reactor.  I calculated temperatures and stresses, but I don’t remember much more than that because I did not write any reports. I was performing tasks as instructed, for someone else’s project. The SEFOR reactor was actually built and operated, successfully serving its experimental purpose. SEFOR means Southeast Fast Oxide Reactor, located in Arkansas.
GE offered continuing education to engineers during their first three years of employment following graduation. I began the A-Course in August of 1963, and the B-Course a year later, in 1964. My B-course classmates were Dana Ditmore and Jim Strang. These two appear in our wedding pictures; I asked them to stand up with me along with my brother Sam and my friend Dick Miller. In 1965 Dana and Jim and I would have begun the C-Course, but GE offered an attractive alternative: a master’s degree from the University of California at Berkeley. We would take one semester of graduate courses beginning in the fall of 1965, to be followed by a master’s thesis.
In March of 1965 I took a permanent position with Sam Tagart in design analysis. This was interrupted by the hiatus for the semester at UC Berkeley, to be fully paid incidentally. Sam and his management were very cooperative. I commuted to Berkeley with my friends Dana and Jim. I took courses in applied mechanics, and in 1966 I completed my thesis, an application of fracture mechanics to reactor piping, postulating a crack in the pipe.
The design basis accident for the nuclear power plant postulated a sudden and complete break of any pipe at any location. There was some pushback from the industry against the regulator on this. Pipes like these don’t just break like that. The pipe break was a reasonable basis for sizing the containment, but were we to design for literally all of the possible consequences of a brittle fracture, when our materials were not brittle? Yes we were. The industry lost that argument. As a result we designed the plant to resist dynamic loads resulting from very hypothetical events. Some of that became part of my job. One of my design analysis projects was to quantify the energy-absorbing capability of pipe whip restraints designed by others.
We were beginning to apply finite element methods to stress analysis of plant components in the late 1960s. A complex shape might defy analysis, but if is simulated by an assembly of many simple shapes, analysis becomes feasible. The limiting constraint is availability of computational horsepower. GE’s mainframe computer was doubling in size and speed every couple of years, or so it seemed. We also needed a sound mathematical definition of the small elements that would be assembled to represent large structures. In 1966 I was responsible for trial applications of an element developed at GE’s aircraft engine division. But in the long run we would use finite elements developed in academia. I soon had in my desk drawer a finite element program based on E. L. Wilson’s work at UC Berkeley.
Wilson’s element was two-dimensional, and easy to use. Joe Rashid, a Berkeley post-doc and Wilson’s associate, had developed a three-dimensional element that some thought to be too costly, in terms of computer time, for ordinary use by ordinary engineers like me. But GE hired Joe Rashid, and I had the good fortune to work with him on an application of his 3-D code. I made the model: a reactor pressure vessel nozzle containing a crack. Dr. Rashid added lines to the code so that we could get the information I needed from a succession of runs. He was the overseer of computations, ensuring that the program ran correctly the first time, every time, and we did not waste GE’s money on this project. I applied principles of fracture mechanics to the interpretation of results. I ran several two-dimensional applications with Wilson’s program to qualify the fracture mechanics interpretation (called strain energy release rate) for the three-dimensional application. The project was a great success (in our view). I presented the results at a conference in Berlin in 1971. I credit Sam Tagart with first envisioning the project and proposing the collaboration. If my goal was to have fun working on interesting technical projects, this was certainly a high point of my professional life.
Judy and I purchased a small house in Los Gatos, moving in shortly after we were married in 1964. In 1968, when Janet and Julie were small, I began a project to expand the family room. My father-in-law helped me on the day we poured concrete, and again when we framed the roof. I did the rest of the measuring and cutting and nailing myself. My neighbor, an electrician, looked over the back fence and advised me that I had located the meter service too far from the corner of the house. I made a joke about having time to do it over, and I took his advice.  I don’t remember all the tasks I must have done alone, after work and on weekends, but I do remember those interactions with other people.
By 1974 I was an acting manager, and then a manager, so I would no longer be doing projects involving finite element analysis; I would watch others do it. My responsibilities as a supervisor expanded to include dynamic and seismic analysis. Two of my engineers were conducting in-plant vibration monitoring of certain reactor internal components. This was required for first-of-a-kind designs. On one or two occasions the monitoring identified a design problem. On one or two occasions, operating experience revealed a vibration problem that we had not thought to monitor. I was deeply involved, with several others, in resolving these issues. I was involved whenever some operating plant component cracked or broke. I would typically be the mechanics specialist on a task force that also included a metallurgist and perhaps a chemist and a plant systems engineer.
 I was also deeply involved with stress corrosion cracking issues after 1974. A small line in an operating plant had cracked and leaked. The pessimists expected to see more cracking incidents, while the optimists looked for reasons to be optimistic. In the long run, the pessimists were right. When I left GE and went to EPRI in 1980, I would be even more deeply involved with stress corrosion cracking in operating plants. My broader technical responsibility at EPRI would be materials performance: how will plant materials perform in service, and how will we fix the problems?
The business outlook for nuclear power turned down after 1973, and it would never recover. GE’s focus now was to deliver what it had sold. Line managers like myself were managing production work. Some senior people left GE to open their own businesses; their expertise had now become valuable to plant operators. Some left because they had been in love with the nuclear power dream and were frankly disillusioned or disappointed by the trend of events. Some left because they missed the excitement of technical innovation in the early years. I suppose my friend Sam Tagart would be among these. Those who stayed, and those who would be hired, needed to be project-oriented: Let’s get this done, and done right. And the work to be done now constituted a number of large group projects. As a manager I had the sense of working on everything every day, but my contribution was to advise, to report progress, and to remove obstacles to progress of whatever sort.
I always saw work extending to the horizon, whether at GE or later at EPRI. As the computer models were compiled, and the design analyses were finished, and the reports were issued, events in operating plants gave us more to do.
In 1975, corporate GE convened a committee in San Jose to report on the company’s remaining obligations and open issues. I did not see the Reed Report while I was at GE, but today it can be found online. A 1987 update summarizes the disposition of technical tasks identified in 1975. This is a good summary of what my GE colleagues were doing in the 1970s. A few of the tasks were mine.
When Tim was not quite two years old, we began to attend the Evangelical Free Church of San Jose (now Hillside Church). This was a time when I was consciously working at assimilating my childhood’s faith and thinking about what I wanted to teach our children. I listened to teachers and made acquaintance with individuals who seemed to have gotten it right. Through the remainder of the 1970s and for many years thereafter I served on committees and held offices in the church. Meanwhile at the end of 1980 I started a new job with the Electric Power Research Institute (EPRI). I had to leave a men’s Bible study which met weekly for breakfast across the street from GE. It may have been those changes which prompted me to undertake a personal project. I worked on this during lunch hour, when I could take a walk in my new semi-rural neighborhood near EPRI. My goal was to express something of my faith in 14 lines of iambic pentameter. The sentiment came from my reflection on the teaching I had been receiving. I composed these lines:

God grant this in the day Thine heirs unite
In celebration of Thy perfect love:
If some have known love’s joy but fleetingly
Complete it then in all who trust in Thee.
 
Lead us in hope to look beyond ourselves
And find among Thy children love’s delight.
Let each share promise, faithfully upheld
And binding us together in Thy sight.
 
Then, self poured out, and thus in Christ fulfilled.
Love’s finest hour: when old desire is stilled
And stirred anew for Him by whom we stand,
As serving we are served by thy sure hand.
 
Then God shall we know Thee, and see Thy face
And share alike the fullness of Thy grace.

                                                                                                JDG  4/81
 

I liked this project for some of the reasons that I liked my construction-set projects as a child. I made it work. I made the pieces fit. I followed the plan. The idea that I expressed could have been said as well in prose, and certainly it would bear prosaic discussion, but I had worked out the meter and rhyme and I found personal satisfaction in that.  

I pursued other writing projects during these years. They were not poetry, so it was more difficult to know when a project was finished. I composed sentences and paragraphs while walking, or driving home from work, or lying in bed at night. When the prose communicated something that I wanted to say, I thought about who would read it. After I had chosen a reader and sent it off, my mind would turn to new subjects and sentences. 

While at GE in 1980 I received a phone call from Sam Tagart, who was working at EPRI. Sam told me of a job opening at EPRI and advised me to apply. I did apply, and I was invited to interview several people at EPRI, but I didn’t get that job. However a short time later I was invited back, and I took a different job. I would be a Project Manager reporting to Robin Jones, and working on stress corrosion cracking issues. I enjoyed a long association with Robin Jones at EPRI. I will add parenthetically that the first job was taken by Bob Nickell, very recently deceased, with whom I also enjoyed a long association. 

As a Project Manager I would not be working on projects. My job was to define a project, to set goals, to write a task description, to estimate cost, and to persuade EPRI’s advisors that the money would be well spent if this project accomplished its stated goals. Then I would assist EPRI’s contract negotiators in identifying the organization and the people who could complete the project. I would meet frequently with contractors to review progress and direction. If the project was successful in the eyes of EPRI and its advisors, I had done my job.  

EPRI’s advisors were engineers and managers from operating nuclear power plants. They needed to know the condition of their plant so it could be operated safely, now and far into the future. They needed to anticipate problems and be ready with solutions. We met quarterly in some American city with our advisory committees, listened to their plant experience reports, and proposed EPRI projects. On a second day of meetings we sought final approvals from a higher level committee of more senior people.  

In my technical area, materials performance, much of the contracted work was done in research laboratories. The researchers were often scientists, not engineers. Their goal was not to make the plant operate; it was to observe and measure and predict the behavior of nuclear plant materials in nuclear environments. The nuclear environment was high pressure, high temperature water. Impurities in the water and in the materials were highly prescribed and carefully controlled. The configuration of materials to be tested and the loads to be applied were also highly prescribed, to be interpreted in accordance with principles of engineering fracture mechanics. Crack growth rates were measured remotely by various clever means. This testing was costly and time-consuming. EPRI funded some of it. I learned that scientists’ stock in trade was credibility among their peers and with funding organizations like mine. The best way to know what scientists really believed was to listen to them talk to each other. Will my data and my interpretation of it stand the test of time? Among engineers, in contrast, the key question was “Will this thing work? Will it fly? Will it serve?” 

Scientists around the world still perform similar testing in support of the world’s nuclear power plants. Beginning around 1979, they met annually to compare notes. Their common goal was to produce good, trustworthy, credible data. I attended several of these meetings during my 18 years at EPRI. Some were in Europe, some in Japan, and some in the USA. For many years the group was known as ICCGR, meaning International Cooperative Group on Cyclic Crack Growth. Later it would be ICG-EAC, where EAC means Environmentally Assisted Cracking. In 2014 the ICG-EAC met in Prague. Some of my younger associates are still participating. These meetings were not the most important part of my job, but this experience was among the most memorable. I do value the many professional associations and friendships I made there. The importance of the work is attested by the fact that, after 35 years these specialists from all over the world are still meeting to talk about nuclear plant materials. 

As an EPRI project manager I made many visits to the laboratories where the work was being performed under contract with EPRI. Most of EPRI’s technical staff were project managers dealing with their own contractors. EPRI project managers had a high degree of autonomy. An aggregate of projects was called a program, and I would eventually be a program manager with supervisory and budget responsibilities, but the project managers guided their technical work.  

I was first hired in 1980 to work on a program dealing with stress corrosion cracking of BWR piping. By the early 1990s the disease had spread, as it seemed, to reactor internals, which were much more difficult and expensive to repair or replace. BWR owners formed the BWR Vessel and Internals Project (BWRVIP) and asked EPRI to manage it. I proposed a task plan and a budget, and got the new project off the ground. In the long term the BWRVIP was managed by my friend Warren Bilanin, whose skills and temperament were better suited to the task. I was still basically a technical guy who had learned some management skills, but Warren was willing and able to spend all day on the phone with customers or in meetings with minions. I was not.  

On the subject of self-analysis, I recall what a supervisor wrote about me back in 1977 at GE: “He tends to be more demanding of himself than his people.” I remembered this because it is true. I worked without being prodded, and I was unwilling to prod a subordinate. Much later, shortly before I retired, my supervisor was prodding me to fire a certain underperforming individual. He explained that if he did not push me to fire this person “you will take the pain”. That was also an accurate observation. I would work overtime to make my subordinates look good. Some of them knew and appreciated the fact. 

I had a friend at EPRI who occasionally stopped by to chat. Mel Lapides usually introduced himself when he walked into my office by saying “it’s interesting ---” and then he would lay out some technical conundrum, or some observation about the way people are or the way the world is wired, and he would often draw some diagram on the board that communicated a universal truth. He made reference to his book, which I gathered would contain many such observations. Mel also mentioned that he had been a writer for Lenny Bruce, and he did have the wit for it. I felt honored by the fact that my visitor was undoubtedly the smartest person in the building (though perhaps not the most productive) and I remember his reference to me on one occasion as the guy who questions everything. We talked about my projects, and his, and other people’s, always being ready to question the conventional wisdom in the industry. 

I was employed in the nuclear power project for nearly 40 years. In retrospect an engineer like myself can say yes, the nuclear power plant works. In 2015 there are 100 water reactors operating in the US, and they have performed very well, especially in recent decades. 35 of these 100 were designed by GE. But success came at a price. Deficiencies in design or materials were identified and remedied; these kept me busy. Operators learned to operate, and regulators learned to regulate, as a result of errors along the way. The Three Mile Island accident was a case in point. More recently some plants have been closed following botched repairs. Some have closed because lower cost power became available in the region. Nuclear power plants, when operated safely and efficiently, are labor intensive, and the necessary staff does not come cheap. 

At Three Mile Island in 1979 the reactor destroyed itself before it was brought under control. The public was not harmed by radiation release but some were harmed by the disruption of evacuation. These outcomes are unacceptable to owners and neighbors of the plant. It is good but it is not enough to say that the public was protected from the radiation hazard. 

More recently in Japan an accident destroyed a nuclear power plant. Radiation was released and again the public was harmed by the evacuation disruption, if not by the radiation. Contamination of the surrounding land was extensive. The cause of the accident was high water that flooded and damaged the emergency power supply. No operating plant can shut down safely without some source of power. 

The cause of the high water was a large tsunami. The plant was designed to withstand a smallish tsunami, but not a large one. Why did engineers choose the smaller number as the design basis, when it was known to some, even then, that much larger tsunamis had occurred near that site?  And why did Japanese regulators accept the smaller number? We have no satisfactory answers, but we have more questions. The design deficiency was recognized in later years, but institutional Japan was unwilling to act. This unwillingness is a subject of the Japanese accident investigation report, published in 2012. The report offers an interesting analysis of Japanese culture. The lesson we should take from the Japanese experience is to ask how American culture, which is very different, could lead to such blatant disregard of apparent risks. As for Japan, I speculate that to adopt a realistic design basis for the tsunami would have meant recognizing that this coastal site is unsuitable for a nuclear power plant. The required high sea wall would have been impractical. That would have been acutely embarrassing in Japan, because the site had already been chosen. 

I am reminded of a conversation I heard at EPRI about the merits of the Japanese approach to regulation of nuclear power. The Japanese authority mandated a lengthy annual outage for every plant. The implicit charge to the operator was to (please) conduct maintenance and inspection activities as necessary during this outage to ensure safe plant operation, and do not embarrass Japan. The US regulatory approach, in contrast, was to make rules and enforce compliance. I believe the US regulator would have asked to see the history of high water along that coast. The Japanese regulator left such technical details to others. Unfortunately, no amount of inspection and maintenance of the operating plant could mitigate the tsunami risk. 

But this was a GE-designed plant. It is fair to ask what GE might have done to mitigate the severe consequences of this accident. I have tried to imagine a GE engineer questioning the tsunami design basis, but success seems unlikely. GE did not have the responsibility or the site-specific historical data. Another set of arguments says that a GE plant of later design would have fared better during the accident, and that is probably true. Finally it is claimed that different actions by a better-informed operator during and after the accident would have reduced the extent of damage. That was also true of the TMI accident. 

Around 1973 I became aware of organized opposition to nuclear power from those who deemed it too dangerous or dirty or difficult to deploy safely. Defenders responded at first by pointing to other activities that were clearly more dangerous and dirty, yet accepted by the American public. The use of coal and the use of agricultural pesticides are two activities that come to mind. But critics made it clear that they did not like these other activities either. This was the beginning of the environmental protection movement. Critics also responded with outrage: How dare you bring this new and risky thing into our community without our permission? The ‘outrage factor’ that I heard about in the 1970s led eventually to a shift of power. It seems unlikely today that a new nuclear power site could be opened, because local opposition and due process could and would prevent it. The nuclear waste disposal site in Nevada at Yucca Mountain has not been opened for just this reason. Local opposition has trumped federal control of federal land. 

Conventional wisdom in the industry held that nuclear power will be deployed if and when people believe it is needed, but not before. Purveyors of nuclear power in the 1970s showed that our standard of living is directly related to consumption of energy. Today our consumption of energy is declining, and our standard of living is also declining, yet the public is unmoved. Apparently other factors trump the standard-of-living argument. 

I was at EPRI when global warming became a public issue. In this arena nuclear power has merit. Energy is produced without the release of greenhouse gasses. But nuclear power advocates at EPRI chose not to press this point because deployment of nuclear power would not be enough to reverse the trend. I heard our director at EPRI say that we ought not to oversell nuclear power as our predecessors did in the 1950s, when someone said it would be too cheap to meter. Today my observation is that nothing we can do will be enough to reverse the increase and produce a reduction in carbon dioxide in the atmosphere. Those who are alarmed by scientific forecasts do not have the geopolitical power to enforce the necessary reduction. The list of actions that must be taken is formidable, and the world is not acting. (Widespread deployment of nuclear power is only one item on the list.) If I am correct there are two possible long-term outcomes. We might learn that carbon dioxide is not, after all, the key to global climate control, and that climate is not changing in the long run as we had feared. Or, climate change will happen and people will adapt to it, as they have in the past, not without difficulty, but successfully. 

Many people believe that science has foreclosed the first possible outcome: we already know that by reducing carbon dioxide emissions we can prevent climate change. But I believe that very few knowledgeable scientists will stand before their colleagues and make this claim. I think many will say that man-made emissions influence climate. Many will say that reduction of emissions is advisable in light of current knowledge. But climate science does not prescribe a solution to climate change. Climate science does not even address the social, political, economic and engineering aspects of CO2 reduction on a global scale. Science describes the problem, but it is a mistake to think that science has the solution. Science is discovery; it is not problem-solving. 

In any case I doubt that the USA will return to nuclear power in the foreseeable future. Our postindustrial society favors technology with a small footprint. Nuclear power belongs to a bygone era of heavy industry and large capital investment and big construction projects. Today we can hardly maintain yesterday’s infrastructure. Young Americans dream of a life off the grid, in which everything is handheld or roof mounted or locally grown. But elsewhere on the globe, nuclear power might well be part of another people’s dream of progress out of want and toward prosperity.
 
I retired from EPRI in 1998. Judy and I relocated to Belchertown in western Massachusetts and purchased a new home. This was our third home, and for the third time we completed several decorating and landscaping projects. During our first year or two in Belchertown I built a gazebo in the back yard. 

I had built a gazebo in San Jose about ten years earlier, so I had time to think about a better way to do it. Instead of conventional rafters and joists I decided on a three-tier roof supported on 8-sided rings. The lower ring would be in tension so it would be assembled with through-bolts. I chose angles and proportions for the roof, and then calculated every length and angle for the framing members, which were all 4x4s. Then I cut and assembled the pieces. Joists were unnecessary, so the ceiling is an open dome. The foundation is a trench filled with large loose rocks, of which we had many on our lot. I had read someplace that a foundation of loose rock does not need to be as deep as the frost line, if it is well drained, so I contrived a rock-filled drainage ditch. I rank the gazebo my favorite construction project. 

In retirement I have acquired tools and made furniture in a basement workshop. I have made quite a few pieces of furniture, and each one was a project. But I also attach value to the experience of learning woodworking. The development of skill is an education; it is never finished. I acquired tools and learned to use them. I read books and followed forums. I tried different techniques and found those that suited me. I learned how much I didn’t know, and became aware of the gap between my skills and those of a lifetime pro. I learned to recognize the work of a few of those pros by their signature designs and design cues.  

Woodworking reminded me of lessons I had learned from my father. To finish a project, start soon, and stay with it until it is done. It will take time, but it won’t take forever. Cutting and fitting dovetail joints, for example, takes time. Go down to the basement and put on some music and get started, and stay until it’s done. 

A more idiosyncratic project was completed in an afternoon several years ago. Every object and location and phenomenon in the cosmos has its characteristic temperature. The internet makes it possible to gather such information. I found that the coldest place in the cosmos is thought to be the Boomerang Nebula, which is about one degree above absolute zero. The hottest place is the hottest star interior, thought to have a temperature of several hundreds of millions of degrees Kelvin. Between these extremes I collected about 30 more interesting observations about temperatures of stars, flames, lava, light bulbs, etc, and placed them on a handsome chart. This is the sort of chart that would have appealed to me when I was 12 years old, if someone had been available to explain the logarithmic scale of temperature. Last year I discussed this chart with a small class of high school physics students. They found the information interesting, more or less. Some doubted that a candle flame could be hotter than molten lava, so we had a useful discussion about that. But I sensed that none of them understood the motive which compelled me to create this chart as a retirement project.  

A similar motive, whatever it was, led me into a more ambitious project. Every place on earth, at every latitude and every season of the year, has its characteristic length of day and length of night. Every latitude and season has its length of morning and evening twilight, during which the sun is not far below the horizon. We can describe twilight periods as either civil twilight, in which one can still read a book outdoors, or nautical twilight, in which the horizon is just visible from a ship at sea. I presented all this information graphically in a few charts on a single board. Many people in every age, especially mariners, even centuries ago, would have understood what the charts depict. The computer and the internet made it possible for me to calculate the numbers on daylight, twilight and darkness and to draw the charts. Others may have done something like this but I could not find their presentations on the internet, so I made my own. 

Another graphical presentation project exists only in my imagination. I shall describe it here so that some like-minded investigator can make it a science project. It is a graph of descending velocity versus size. I have in mind the velocity of objects descending toward the earth under the influence of gravity. The slowest velocities are at the top of the graph. These might be the settling rate of fine dust in the atmosphere, or the sinking rate of tiny diatoms in the sea; perhaps some fraction of one meter per day. And these are among the smallest objects which fall. Smaller objects will be held in suspension by Brownian motion; they will not descend; they will form a colloidal suspension. So these small-and-slow phenomena are displayed near the upper left hand corner of the graph. Then near the opposite corner of the graph are the largest objects falling at the highest velocity imaginable. An asteroid originating in the solar system and travelling directly toward the earth would enter the atmosphere at a velocity as high as 72 thousand meters per second. The atmosphere will slow it down, but if the asteroid is very large the atmosphere will not slow it much. These large-and-fast phenomena are displayed near the lower right hand corner of the graph. Everything else will display somewhere near the diagonal line between these corners. 

Clearly we will need logarithmic scales to display the very wide range of sizes and velocities. We will do some research to discover the falling velocities of raindrops and snowflakes and hailstones in the atmosphere. We will discover that large raindrops break up into smaller drops, so that raindrops cannot be as large or fall as fast as hailstones. Stones fall faster than hail, and lead shot falls faster than stone, for spheres of the same size. Different classes of objects will fall on different parallel lines on this graph. We will need to compute terminal velocities, if someone hasn’t done it for us, which is the reason this project won’t be easy to complete. 

If an object is not a sphere we can still assign it a size for our purposes. The size of an arrow, for example, might be characterized by the size of the imaginary hole it makes in the atmosphere as it falls. The arrowhead and the feathers determine the size. I read someplace that the Titanic struck the ocean floor at a velocity of 35 knots. The size of the hull might be characterized by the beam, or by the average of beam and height. Because we are displaying size on a logarithmic scale, it won’t matter much. We can put the Titanic on the chart of descending velocity versus size. We can also put a baseball and a skydiver and a peregrine falcon on this chart. 

Why would anyone like to do this? For the same reason that I would like to do it. 

Judy is a photographer. She brings her camera and waits for the shot, or she persuades people to line up for the group photo. I am not good at those things. But I did complete a photography project back in the 1980s. I had a pretty good film camera. I built a stand for it, bought a close-up attachment, and copied many of the old family photos that I found in borrowed albums and frames.  When the internet became available I followed some genealogy forums, made some personal contacts, and acquired some old photos that we had not seen and some family history that we did not know. More recently I have scanned the copies of photos and collected them on my hard drive.  

Mother wanted to preserve the story of her family in Texas, before they came to California in 1919. In the late 1980s I gathered up what she had and wrote a few paragraphs on the Nuckols, Hill, Bishop and Friou families. That writing project needs to be updated, because more information about the old days has become available as a result of the internet, and some of what we thought we knew is not quite accurate.  

Later I wrote a history of our Gilman family, and another of the Douglass family of Randolph County Illinois. Both of these are about times that are out of living memory. The challenge for me is to find all the relevant information that can be found and to weave it into a story. The project is finished when there is nothing more to be found. I am aware of a few bits of information in my files that need to be added, so these projects are never quite finished. And family members, including me, occasionally remember another story they heard years ago. 

The histories of families we know emerge from a larger context in American history. Why did these individuals choose to move from location A to location B during these years? Often the answers can be gleaned from history books. They were part of a larger movement, and other families shared the same history. Invariably, in our accounts of family history in the 19th century, location B was west of location A. Here is another measure of a writing project on family history: it is complete when it connects with larger history. 

A year ago I was teaching physics to high school students. Teaching is decidedly not a project; it is a stand-up performance. Even a physics teacher needs to be in the moment, as they say, when talking to teenagers. I enjoyed teaching six relatively cooperative students at Community Christian School; I might not have enjoyed teaching a large class in a public school. But in either case I could not have done this when I was a young man. It required a lifetime for me to become sufficiently spontaneous and articulate, even when my subject was as comfortable and familiar as physics. Teaching physics was surely one of the best things I have done in retirement. I enjoyed dusting off and talking about some of my old projects, like the homemade electric motor, and a crystal set from Boy Scout days. I talked about how things work, and I learned how to explain some less familiar things like the elementary principles that produce the Aurora Borealis. 

In 2003 I had for some reason a few lines of text in my head, so I decided to write these down. One idea led to another, and I composed a series of essays during the next few years. These may be found here.
                                http://joestripreport.blogspot.com/ 

Also on this site are a few sermons that I wrote out before I delivered them on a Sunday morning at our little church. I did not preach a sermon anywhere until I was nearly 70 years of age. Like teaching high school, I was not up to it when I was younger. 

The writing project I began in 2003 might be finished; I can’t be sure. Maybe the essay muse will visit me again. This current writing project is much different. It required only a few weeks from start to finish. 

Joe Douglass Gilman Jr.
February 2015